产 品 规 格 书 product specification 【1】适用范围 scope 本规格书适用于: 0.5间距柔性扁平电缆连接器(有锁式) this specification cove the 0.5mm pitch fpc/ffc connecto ( series locking ) 【2】产品名称及型号 product name and part number 产品名称 product name 产品型号 part number ffc/fpc 扁平电缆连接器 【3】定格 ratings 项目 item 规 格 requirement 大容许电压 rated voltage(max) 50v [ac/dc( 有效值 virtual value)50hz] 大容许电流 rated current(max) 0.4a 使用温度范围 ambient temperature range -25 ℃ ~ +85℃ 【4】性能 performance 4.1 电气性能 electrical performance 项目 item 条 件 test condition 规格 requirement 4.1.1 接触电阻 contact resistance 适合 fpc/ffc 嵌合;开放电压 20mv 以下;短路电流 10ma 的状态下测定。 mate applicable fpc/ffc and measure by dry circuit , 20mv max , 10ma. ≤2 0 m ω max 4.1.2 绝缘电阻 iulation resistance 适合 fpc/ffc 嵌合;相邻端子间或端子与地面间加 dc 500v 下测定。 mate applicable fpc/ffc and apply 500v dc between adjacent terminal or ground. 500m ω min 4.1.3 耐电压 dielectric 适合 fpc/ffc 嵌合;相邻端子间或端子与地面间加 ac 200v (有效值)历时 1 分钟下测定。 mate applicable fpc/ffc and apply 200v ac ( virtual value ) for 1minute between adjacent terminal or ground. 无击穿现象 no breakdown 4.2 机械性能 mechanical performance 项目 item 条 件 test condition 规格 requirement 4.2.1 锁紧力及拔出力 locking and withdrawal force 适合 0.3mm 厚的 ffc ;用每分钟 25 ± 3mm 的速度;平行地插入、锁紧、拔出。 iert and extract applicable ffc at the speed rate of 25 ± 3mm/minute. 锁紧力 locking 1.96*n (n) max 拔出力 withdrawal 0.49*n (n) min 4.2.2 端子保持力 terminal /housing retention force 以用每分钟 25 ± 3mm 的速度平行向外拉 pull the terminal at the speed rate of 25 ± 3mm per minute 3.92n min 4.3 环境和其他性能 environmental performance and othe 项目 item 条 件 test condition 规格 requirement 4.3.1 重复插拔 repeated iertion and withdrawal 无通电状态;以 10 次 / 分钟的速度插拔 20 次 iertion and withdrawal actuator up to 20 cycles at the speed rate of less than 10 cycles/minute 接触抵抗 contact resistance 60 m ω max 4.3.2 温度上升 temperature rise 适合 fpc/ffc 嵌合;大容许电流通电,温度测定。( ul 498 ) carrying rated current load. ( ul 498 ) 温度上升 temperature rise 30 ℃max 项目 item 条 件 test condition 规格 requirement 4.3.3 耐振动性 vibration dc 1ma 通电状态下;嵌合轴沿 xyz 三个方向振动;振幅 1.5mm ;频率 10-55-10hz/ 分;历时 2 小时 amplitude : 1.5mm p-p sweep time : 10-55-10hz in 1 minute duration : 2 hou in each x.y.z. axes 外观 appearance 无损坏 no damage 接触抵抗 contact resistance 60 m ω max 瞬断 discontinuity 1 ms max. 4.3.4 耐冲击性 shock dc 1ma 通电状态下;嵌合轴沿相互垂直的 6 个方向;以 490m2{50g} 冲击;各 3 次 490m2{50g} , 3 strokes in each x.y.z. axes. 外观 appearance 无损坏 no damage 瞬断 discontinuity 1 ms max. 4.3.5 耐热性 heat resistance 适合 fpc/ffc 嵌合; 85 ± 2 ℃的空气中;放置96小时;再回到室温中放置1-2小时 85 ± 2 ℃,96 hour 外观 appearance 无损坏 no damage 接触抵抗 contact resistance 60 m ω max 4.3.6 耐寒性 cold resistance 适合 fpc/ffc 嵌合; -40 ± 2 ℃的空气中;放置96小时;再回到室温中放置1-2小时 -40 ± 2 ℃,96 hour 外观 appearance 无损坏 no damage 接触抵抗 contact resistance 60 m ω max 4.3.7 耐湿性 humidity 适合 fpc/ffc 嵌合; 40 ± 2 ℃、相对湿度90-95%的空气中;放置96小时;再回到室温中0.5小时内测定 temperature : 40 ± 2 ℃ relative humidity :90-95% duration :96 hou 外观 appearance 无损坏 no damage 接触抵抗 contact resistance 60 m ω max 耐电压 dielectric strength 必须满足4.1.3 must meet 4.1.3 绝缘抵抗 iulation resistance 20 m ω min 4.3.8 温度循环 temperature cycling 适合 fpc/ffc 嵌合; -55 ± 3 ℃ 30分钟;常温常湿 10-15分钟; 85 ± 2 ℃ 30分钟;常温常湿 10-15分钟, 循环 5 次。 5 cycles of : a) -55 ± 3 ℃ 30 minutes b) 85 ± 2 ℃ 30 minutes 外观 appearance 无损坏 no damage 接触抵抗 contact resistance 60 m ω max 项目 item 条 件 test condition 规格 requirement 4.3.9 耐盐雾性 salt spray 适合 fpc/ffc 嵌合; 35 ± 2 ℃、5 ± 1% 的盐水喷雾 48 小时;试验后常温水洗;再室温干燥。 48 ± 4 hou exposure to a salt spray from the 5 ± 1% solution at 35 ± 2 ℃. 外观 appearance 无损坏、腐蚀 no damage 接触抵抗 contact resistance 60 m ω max 4.3.10 耐亚酸 so2 gas 适合 fpc/ffc 嵌合; 40 ± 2 ℃、50 ± 5ppm 的亚酸中放置 24 小时 24 hou exposure to 50 ± 5ppm. so2 gas at 40 ± 2 ℃. 接触抵抗 contact resistance 60 m ω max 4.3.11 耐性 nh3 gas 适合 fpc/ffc 嵌合;浓度为 28 % 的水容器中;放置40分钟。 40 minutes exposure to nh3 gas evaporating from 28% ammonia solution 外观 appearance 无损坏 no damage 接触抵抗 contact resistance 60 m ω max 4.3.12 可焊性 solder ability 端子前端基准面 0.2mm 处浸入 235 ± 5 ℃的锡槽中;历时 2 ± 0.5 sec 。 soldering time : 2 ± 0.5 sec. soldering temperature : 235 ± 5 ℃ 0.2 mm from terminal tip 沾敷性 solder wetting 沾敷面积 95% 以上 4.3.13 耐焊接热 resistance to soldering heat 端子前端基准面 0.2mm 处浸入 260 ± 5 ℃的锡槽中;历时 5 ± 0.5 sec 。 soldering time : 5 ± 0.5 sec. soldering temperature : 260 ± 5 ℃ 0.2 mm from terminal tip 外观 appearance 无损坏、变形 no damage 本产品的加工定制是否,品牌是mstconn,型号是0.5k-dx-npwb,应用范围是pcb,种类是ffc/fpc,接口类型是zif,形状是条形,制作工艺是冷压,特性是阻火/阻燃,工作频率是低频,接触件材质是磷青铜,绝缘体材质是lcp,芯数是4-18p
详细介绍
深圳市德瑞电子有限公司其他商品
PCB连接器相关分类
- 插头、插座
- AC-DC连接器
- 端子(terminal)
- 电脑连接器
- 电缆连接器
- USB连接器
- PCB连接器
- 电源连接器
- 线束、连接线、端子线
- 汽车连接器
- 通讯连接器
- 手机连接器
- 端子排、接线排(条)
- 闭端子(压线帽)
- 端子盘
- 屏线、斑马纸
- 传感器连接器
- 鳄鱼夹、弹簧夹、电瓶夹
- 端子台、接线柱(头)
- 光纤端子
- 接线座、接线板
- 扬声器(喇叭)连接器
- 排针、排母、排线
- 转接头
- 电池连接器
- HDMI连接器
- 水晶头
- AV连接器
- IC连接器
- 汇流排(总线)
- 针座、插针
- 简牛、牛角
- S-video端子
- DispalyPort
- 板对线连接器
- WAFER连接器
- 显示屏连接器
- 1394连接器
- BNC连接器
- DVI连接器
- SCSI连接器
- 卡座(读卡器连接器)
- 护套
- 射频同轴(RF)连接器
- LED连接器
- 线对线连接器
- DC-DC连接器
- RJ45连接器
- D-SUB(VGA)端子
- IDC连接器
- 板对板连接器
- SATA、ATA连接器
- 光纤连接器
- 胶壳(housing)
- ZIF连接器
- PCI连接器
- DIN(大、中、小)
- FFC、FPC连接器
- IPOD连接器
- HDR连接器
- 背板连接器
- PLCC连接器
- 端子接插件
- 航空连接器